| 1 | Ground levelling zone. It can be used well in seedbed preparation. |
| 2 | Loosening zone. Loosening depth 4–15 cm. Optimized geometry chisels in four rows with small final spacing ensure very fine full-area loosening and intensive soil mixing with plant residues. |
| 3 | Wave-levelling zone. Levelling discs also increase the effect of incorporating plant residues. |
| 4 | Clod crumbling and soil reconsolidation zone. Optimum soil reconsolidation ensures good water infiltration and soil moisture rise. |
Half mounted 4-row share cultivator Fantom CLASSIC with low traction resistance and variable processing depth up to 15 cm.
Intensive and fine soil processing is enabled due to the tine spacing of 170 mm. There is a spring protection on the tines with a very high release force of 310 kg on the tip of the ploughshare. The working width of the cultivator is stable even in more difficult conditions.
Half mounted 4-row share cultivator Fantom CLASSIC with low traction resistance and variable processing depth up to 15 cm.
Intensive and fine soil processing is enabled due to the tine spacing of 170 mm. There is a spring protection on the tines with a very high release force of 310 kg on the tip of the ploughshare. The working width of the cultivator is stable even in more difficult conditions.
Due to minimum of adjusting and lubricating points the operation and subsequent maintenance are very easy steps that anybody can perform.
The advantage of this machine is its multipurposeness and adjustability bringing high variability of work.
| Technical parameters | Units | Fantom 650 CLASSIC |
Fantom 850 CLASSIC |
Fantom 1250 CLASSIC |
|---|---|---|---|---|
| Working width | mm | 6 300 | 8 550 | 12 250 |
| Transport width | mm | 3 000 | 3 000 | 3 000 |
| Transport height | mm | 3 650 | 4 000 | 4 000 |
| Total machine length | mm | 8 000 | 8 700 | 8 200 |
| Working depth | mm | 40–150 | 40–150 | 40–150 |
| Number of ploughshares | pcs | 33 | 45 | 64 |
| Ploughshare spacing | mm | 190 | 190 | 190 |
| Number of ploughshare rows | pcs | 4 | 4 | 4 |
| Row spacing | mm | 595–620 | 595–620 | 595–620 |
| Release force of ploughshares | kg | 310 | 310 | 310 |
| Frame clearance | mm | 570 | 570 | 570 |
| Working performance | ha/h | 4,4–7,2 | 6,8–10,2 | 10,0–15,0 |
| Towing vehicle 1 | kW HP |
200–300 270–410 |
245–370 330–500 |
330–440 450–675 |
| Working speed | km/h | 8–12 | 8–12 | 8–12 |
| Maximum transport speed 3 | km/h | 30 | 30 | 30 |
| Maximum slope availability | ° | 6 | 6 | 6 |
| Number of hydraulic circuits / pressure | bar | 5 / 200 | 5 / 200 | 5 / 200 |
| Number of hydrocouples / type | 8 / ISO 12,5 | 8 / ISO 12,5 | 8 / ISO 12,5 | |
| Tractor hitch requirement | TPH cat. 3; peg Ø 50, 70 mm; hinge K80 | TPH cat. 3; peg Ø 50, 70 mm; hinge K80 | peg Ø 50, 70 mm; hinge K80 | |
| Machine weight 2 | kg | 7 000 | 8 900 | 12 400 |
1 Recommended towing vehicle, the actual pulling force may significantly change according to the processing depth, soil conditions, inclination of land, wear of working members and their adjustment.
2 Depends on the type of the roller used.
3 Transport / brake system: Follow national provisions valid for transport of machines on public roads. Verify legal provisions valid in the country, regulations on maximum allowable total weights and axle loads and also on necessary possible use of the brake system. If you have any questions, please contact our sales representative.
| Diameter | 580 mm |
| Weight | 220 kg/m |
| Diameter | 586 mm |
| Weight | 200 kg/m |
LTX roller cannot be used for Fantom 850 CLASSIC.
| Diameter | 600 mm |
| Weight | 100 kg/m |
| Diameter | 550/550 mm |
| Weight | 180 kg/m |
Double V-ring cannot be used for Fantom 1250 CLASSIC.
| Diameter | 540/540 mm |
| Weight | 195 kg/m |
Double ring roller cannot be used for Fantom 1250 CLASSIC.
| Diameter | 600 mm |
| Weight | 175 kg/m |
| Diameter | 520/520 mm |
| Weight | 165 kg/m |
Proper selection of the type of the rear roller contributing significantly to the final quality of the processing is very important. The soil is recompacted by the roller and then it is the same way crumbled and levelled. The selection of the type of the roller depends on the soil type and on the manner of use of the machine.
| Roller | Tube-shaped TRS |
Double ring DRR |
Double DFR |
LTX |
|---|---|---|---|---|
| Crumbling | ●●○○ | ●●●○ | ●●●○ | ●●○○ |
| Stamping | ●●●○ | ●●●● | ●●●● | ●●●● |
| Depth guiding | ●●●○ | ●●●● | ●●●● | ●●●● |
| Resistance against clogging | ●○○○ | ●●●● | ●●●● | ●●●○ |
| Suitability for stony soils | ●●●○ | ●●●○ | ●●●○ | ●●●○ |
| Suitability for wet soils | ●○○○ | ●●●● | ●●●● | ●●●● |
| Heavy soils | ●●○○ | ●●●● | ●●●● | ●●●● |
| Medium soils | ●●●○ | ●●●● | ●●●● | ●●●● |
| Light soils | ●●●● | ●●●● | ●●●● | ●●●○ |
| Roller | Disk SDR |
VR | Double V-ring DVR |
|---|---|---|---|
| Crumbling | ●●●○ | ●●●○ | ●●●○ |
| Stamping | ●●●● | ●●●● | ●●●● |
| Depth guiding | ●●●● | ●●●● | ●●●● |
| Resistance against clogging | ●●●○ | ●●●● | ●●●● |
| Suitability for stony soils | ●●●○ | ●●●○ | ●●●○ |
| Suitability for wet soils | ●●●● | ●●●● | ●●●● |
| Heavy soils | ●●●● | ●●●● | ●●●● |
| Medium soils | ●●●● | ●●●● | ●●●● |
| Light soils | ●●●○ | ●●●● | ●●●● |
| Share width | 50 mm |
| Share body hardness | up to 55 HRC |
| Widia plate hardness | up to 92 HRA |
| Hardness of hard facing | up to 60 HRC |
| Share service life | + 400-600 % |
| Share width | 50 mm |
| Share body hardness | up to 55 HRC |
| Widia plate hardness | up to 92 HRA |
| Share width | 280 mm |
| Share body width | 43 mm |
| Share thickness | 6 mm |
| Body hardness | up to 55 HRC |
| Carbide plate hardness | up to 92 HRA |
For all-area undercutting
| Share width | 50 mm |
| Share body hardness | up to 55 HRC |
| Widia plate hardness | up to 92 HRA |
| Share service life | + 400-600 % |
| Share width | 230 mm |
| Share thickness | 8 mm |
| Body hardness | up to 55 HRC |
Divides 1 tractor circuit into 3 circuits.
